|
ΤΗΛΕΧΕΙΡΙΣΤΗΡΙΟ ΓΙΑ ΤΗΛΕΟΡΑΣΗ - ΒΙΝΤΕΟ - ΔΟΡΥΦΟΡΙΚΟ - DVD - 2η ΤΗΛΕΟΡΑΣΗ .
ΥΠΟΣΤΗΡΙΖΕΙ ΠΕΡΙΠΟΥ 350 ΜΑΡΚΕΣ ΑΛΛΑ ΚΥΡΙΩΣ ΤΙΣ ΒΑΣΙΚΕΣ ΛΕΙΤΟΥΡΓΙΕΣ.
ΕΙΝΑΙ ΠΟΛΥ ΕΛΑΦΡΥ ΚΑΙ ΕΥΧΡΗΣΤΟ ΚΑΙ ΠΟΛΥ ΛΕΠΤΟ.
ΛΕΙΤΟΥΡΓΕΙ ΜΕ 2 X CR 2032 Η ΟΠΟΙΑ ΠΕΡΙΛΑΜΒΑΝΕΤΑΙ.
This remote replaces to 4 separate remote
controls to operate your infrared controlled
television (TV), video cassette recorder
(VCR), satellite receiver (SAT) cable TV
conversor (CTV).
1.- BEFORE SETTING UP THE
URC
Two (2) CR2025 lithium batteries are put
inside the
battery compartment together with one
battery
protector for insulation. Before perating
the URC,
you need to remove the battery protector
first.
2.- HOW TO SET UP THE
URC
There are 4 Device Modes (TV, VCR, SAT
& AUX) in your URC. You may setup the
URC by following code entering or
searching instructions.
By Entering Device
Code
1.- Refer to the Device Code List (at the
back of this sheet), look up the 4-digit device
code which corresponds to the brands of
your A/V equipment. lf there are
more than one Device Code listed under
your brand, try from the first code.
2.- Press a desired Device Mode Key (e.g.
).
3.- Hold down key for 2 seconds until the
indicator lights up.
4.- Use the number keys “0”-“9” to enter
your 4-digit device code; the indicator
should go out immediately.
5.- Turn on your device manually (e.g.
TV), try the function keys on the URC. lf your
device (e.g. TV) responds to your invoked
function correctly, you have entered the
right Device Code. Otherwise, repeat the
above setup instructions with the rest
available Device Codes until your device
(e.g. TV) responds to your invoked
function, and most keys work
correctly.
Note: CTV and other Device Codes can be entered
into “SAT” & “AUX” modes.
Simply repeat the above procedures to
enter the device codes for your VCR, SAT or
CTV. Remember to press a correct Device
Mode Key in step 2 above.
lf the indicator flashes twice during the
above procedures, a wrong device code has
been entered. You are required to repeat
step 2 to 5 again.
By Searching Through the
Library
If you cannot find a correct Device Code
for your equipment from the Device Code
List, you may search the code through the
library.
1.- Turn on your device manually
.
2.- Press a desired Device Mode Key (e.g.
).
3.- Hold down key for 2 seconds until the
indicator lights up.
4.- Enter a corresponding Magic Search
Code from following table and the indicator
should go out immediately.
5.- Press the same desired Device Mode Key
again as in step 2 above (e.g. ).
6.- Hold down key for 2 seconds until the
indicator lights up.
7.- Aim the URC at your device (e.g. TV),
press key repeatedly, slowly and
patiently until the device has been turned
off. Once your device has been turned
off, immediately press key to lock in code
and the indicator should go out.
lf you failed to stop pressing in time
when your device has been turned off, turn
on your device again immediately. Before
the indicator goes out, press on the
URC to skip backward. Repeat step 7 above
and lock in code.
Simply repeat the above procedures to
search the device codes for your VCR, SAT
or CTV. Remember to press a correct Device
Mode Key & corresponding Magic
Search Code
above.
Note: CTV and other device codes can be searched
and locked into SAT/AUX
mode. Just simply press SAT/AUX Device
Mode Key in step 2 & 5 and enter
en appropriate Magic Search Code for CTV
or other devices.
If the power on/off function of your
device is not infra-red controlled, you need
to follow steps 2 to 6 above and start
searching. Then, press and another
important function key alternately until
your device responds to the expected
function, press key to lock in
code.
e.g. Press &
alternately.
3.- OPERATING THE
URC
To operate, just aim it at your equipment,
press an appropriate device mode key and
invoke the desired function by pressing a
corresponding key on the URC. The
indicator flashes during signal
transmission and as confirmation of key
touch.
|
